Alerts
Loading...
| Signal Name | Description | Condition | Impact | Important |
|---|---|---|---|---|
|
The vehicle controller detects one or more loads did not turn off after the self-test commanded them off, or they did not turn on when the self-test commanded them on.
|
One or more loads did not turn off after the self-test commanded them off, or they did not turn on when the self-test commanded them on
|
The vehicle is unable to drive.
|
No
|
|
|
The vehicle controller detects an undercurrent condition on the front trunk (or frunk) strut actuator, indicating the 48V rail may be down.
|
Firmware is commanding the frunk strut to actuate but the strut actuator draws less than 50mA for 300ms, and the velocity of the actuator is less than 1 deg/s.
|
The front trunk strut may be unable to actuate, preventing the front trunk from opening or closing.
|
No
|
|
|
The bridge gate driver experienced a condition affecting its operation.
|
The bridge gate driver reports a condition affecting its operation.
|
Actuators controlled by the bridge gate driver may be inoperative.
|
No
|
|
|
One or more loads failed to turn on during the Right Domain Undervoltage Self-Test. Those loads will be inhibited from use in drive.
|
One or more loads failed to turn on during the Right Domain Undervoltage Self-Test.
|
Impacted load(s) will not be usable in drive.
|
No
|
|
|
The Right Domain Undervoltage self-test did not pass, as a condition affecting a load on the Right Domain was detected during the self-test.
|
The Right Domain Undervoltage self-test does not succeed.
|
The undervoltage protection circuit may not be functional.
|
No
|
|
|
Low Tone Trumpet Horn is drawing more current than expected.
|
Horn current is above the expected value.
|
Horn(s) may not sound.
|
No
|
|
|
Horn is drawing less current than expected.
|
Horn current is below the expected value.
|
Horn(s) may not sound.
|
No
|
|
|
The upper hard stop limit for the seat backrest is disabled, meaning the seat backrest is allowed to move forward past the upper hard stop limit if requested.
|
The upper hard stop limit for the seat backrest is disabled.
|
The seat backrest is allowed to move forward past the upper hard stop limit and may interfere with the sunvisor.
|
No
|
|
|
The seat backrest has reached the upper hard stop limit and cannot move forward any further.
|
The position of the seat backrest moves forward and is above the upper hard stop limit.
|
The seat backrest will not move forward.
|
No
|
|
|
The seat lift motor encoder has unexpectedly stalled.
|
Current draw exceeds 70% of the stall limit, and the encoder does not move for 100ms.
|
The seat lift motor encoder may increment incorrectly if an obstruction is encountered.
|
No
|
|
|
The seat tilt motor encoder has unexpectedly stalled.
|
Current draw exceeds 70% of the stall limit, and the encoder does not move for 100ms.
|
The seat tilt motor encoder may increment incorrectly if an obstruction is encountered.
|
No
|
|
|
The seat track motor encoder has unexpectedly stalled.
|
Current draw exceeded 70% of the stall limit, and the encoder did not move for 100ms.
|
The seat track motor encoder may increment incorrectly if an obstruction is encountered.
|
No
|
|
|
The seat lift motor has unexpectedly stalled.
|
Current draw exceeds stall limit.
|
Motor will recalibrate if the stall is in an expected region, do nothing otherwise.
|
No
|
|
|
The backrest motor has unexpectedly stalled, which may cause the motor to recalibrate.
|
The current draw of the backrest motor has exceeded the stall limit.
|
If the stall occurs in an expected region, the backrest motor may recalibrate.
|
No
|
|
|
The seat tilt motor has unexpectedly stalled.
|
Current draw exceeds stall limit.
|
Motor will recalibrate if the stall is in an expected region, do nothing otherwise.
|
No
|
|
|
The seat track motor has unexpectedly stalled.
|
Current draw exceeds stall limit.
|
Motor will recalibrate if the stall is in an expected region, do nothing otherwise.
|
No
|
|
|
The seat motor has traveled beyond the expected range.
|
Seat position goes outside the acceptable range.
|
Seat may be in an unstable position or a mechanism may not be functioning as expected.
|
No
|
|
|
The seat track motor is not calibrated, which may cause position recall to be unavailable.
|
The seat track motor is detected as uncalibrated (calibrated state of the seat track motor is 0).
|
Position recall may be unavailable, meaning the preset user preferences for seat positions may also be unavailable.
|
No
|
|
|
One or more expected Controller Area Network (CAN) messages from the Audio Digital Signal Processor (ADSP) electronic control unit (ECU) was not received. ADSP data from accelerometers may be unavailable.
|
One or more expected CAN messages from the ADSP is not successfully received. May be due to missing message(s), message reception rate error, or invalid checksum / counter error (message is too short / long, the checksum does not match, or unexpected sequence errors are present).
|
Air suspension functionality may be reduced. Excessive leveling corrections may occur. Active damping control may be disabled.
|
No
|
|
|
Etherloop Generalized Gateway (EGGREAR) detects a condition affecting REARSTEER CAN bus. Alert log signal data should provide more information on specific condition.
|
Number of CAN transmit or receive errors exceeds 127.
|
EGGREAR is unable to transmit or receive messages on REARSTEER CAN bus, making communication unavailable.
|
No
|