Alerts
Loading...
| Signal Name | Description | Condition | Impact | Important |
|---|---|---|---|---|
|
iBooster (IBST) detected a failure in the metal-oxide-semiconductor field-effect transistor (MOSFET) bridge driver supply switch.
|
IBST detects a failure in MOSFET bridge driver supply switch.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected a bridge metal-oxide-semiconductor field-effect transistor (MOSFET) shorted error.
|
IBST detects a bridge MOSFET shorted error.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected an application-specific integrated circuit (ASIC) internal error.
|
IBST detects an ASIC internal error.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected an application-specific integrated circuit (ASIC) internal error.
|
IBST detects an ASIC internal error.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected data reception did not complete within the expected time interval.
|
IBST detected data reception did not complete within the expected time interval.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected data reception did not complete within the expected time interval.
|
IBST detected data reception did not complete within the expected time interval.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected an ECU output (UEXS) over-temperature condition and has been switched off.
|
UEXS has over-temperature and has been switched off.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected maximum allowed time to start the system has been reached.
|
IBST detects maximum allowed time to start the system is reached.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected an SMM information failure.
|
IBST detects an SMM information failure.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected Rotation Position Sensor (RPS) Cos+ or Cos-signal too high.
|
IBST detected RPS Cos+ or Cos-signal too high.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected Rotation Position Sensor (RPS) Sin+ or Sin-signal too high.
|
IBST detected RPS Sin+ or Sin- signal too high.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected Rotation Position Sensor (RPS) Cos+ or Cos-signal too low.
|
IBST detected RPS Cos+ or Cos-signal too low.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected Rotation Position Sensor (RPS) Sin+ or Sin- signal too low.
|
IBST detected RPS Sin+ or Sin- signal too low.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected UBB voltage is above shutdown threshold (overvoltage level 3).
|
IBST detected UBB voltage is above shutdown threshold.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected UBB supply voltage is below shutdown threshold (undervoltage level 3).
|
IBST detected UBB supply voltage is below shutdown threshold.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) Controller Area Network (CAN)-Driver: Timeout caused by Hardware (HW)-Error (CAN-Controller configuration failed).
|
IBST detects CAN-Driver Timeout caused by a HW-Error.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected spindle position value is higher than the physical limited values.
|
IBST detected spindle position value is higher than the physical limited values.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected a permanent deviation between the target speed and the actual motor speed.
|
IBST detected a permanent deviation between the target speed and the actual motor speed.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) detected differential travel is permanently not compensated.
|
IBST detected differential travel is permanently not compensated.
|
IBST may not operate as expected.
|
No
|
|
|
iBooster (IBST) firmware set in case of temperature degradation level 2.
|
IBST firmware set in case of temperature degradation level 2.
|
IBST may not operate as expected.
|
No
|