Alerts
Loading...
| Signal Name | Description | Condition | Impact |
|---|---|---|---|
|
iBooster (IBST) detected Rotation Position Sensor (RPS) Sin+ or Sin- signal too low.
|
IBST detected RPS Sin+ or Sin- signal too low.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected UBB voltage is above shutdown threshold (overvoltage level 3).
|
IBST detected UBB voltage is above shutdown threshold.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected UBB supply voltage is below shutdown threshold (undervoltage level 3).
|
IBST detected UBB supply voltage is below shutdown threshold.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) Controller Area Network (CAN)-Driver: Timeout caused by Hardware (HW)-Error (CAN-Controller configuration failed).
|
IBST detects CAN-Driver Timeout caused by a HW-Error.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected spindle position value is higher than the physical limited values.
|
IBST detected spindle position value is higher than the physical limited values.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected a permanent deviation between the target speed and the actual motor speed.
|
IBST detected a permanent deviation between the target speed and the actual motor speed.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected differential travel is permanently not compensated.
|
IBST detected differential travel is permanently not compensated.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) firmware set in case of temperature degradation level 2.
|
IBST firmware set in case of temperature degradation level 2.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) firmware set in case of temperature degradation level 1.
|
IBST firmware set in case of temperature degradation level 1.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) wear offset value not able to read from Non-volatile Memory (NVM).
|
IBST wear offset value not able to read from NVM.
|
IBST may not operate as expected.
|
|
|
Indicates IBST pRunout brake pressure was not reached due to motor torque output saturation.
|
Set when IBST cannot reach pRunout with full motor torque output. 300ms debounce time.
|
iBooster will have smaller EBR bandwidth but EBR will be executed by ESP thus no change in overall EBR bandwidth. If motor torque is saturated below legal deceleration limit, the PSD (a082) will be set.
|
|
|
iBooster (IBST) read failed failure for parameter MasterCylinderLength.
|
IBST read failed failure for parameter MasterCylinderLength.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected the find idle routine in plant failed.
|
IBST detected the find idle routine in plant failed.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected find idle data can not be written in the find idle calibration routine in plant/service (Rotation Position Sensor (RPS) angle at backward bound and idle and lips IDs).
|
IBST detects find idle data can not be written in the find idle calibration routine in plant/service.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected Non-volatile Memory (NvM) value for the GapLap JI-Adjust is not readable.
|
IBST detects NvM value for the GapLap JI-Adjust is not readable.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected backward bound could not be detected during greasing routine, resulting in a time out.
|
IBST detected backward bound can not be detected during greasing routine - Time out.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected charge Pump Tests/Monitor could not be executed due to an undervoltage condition.
|
IBST detected charge Pump Tests/Monitor could not be executed due to an undervoltage condition.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected Brushless Motor (BLM) temperature sensors are not plausible voltage values.
|
IBST detects a BLM temperatures are not plausible voltage value.
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected Brushless Motor (BLM) temperature sensor 1 line shorted to supply.
|
IBST detects BLM temperature sensor 1 line shorted to supply.o
|
IBST may not operate as expected.
|
|
|
iBooster (IBST) detected Brushless Motor (BLM) temperature sensor 2 line shorted to ground.
|
IBST detects BLM temperature sensor 2 line shorted to ground.
|
IBST may not operate as expected.
|