Alerts
Loading...
| Signal Name | Description | Condition | Impact | Important |
|---|---|---|---|---|
|
Not Available
|
The desired state of the ambient lighting could not be set, the current state is not the expected one or the brightness adjustment did fail.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
The glove box latch did not open or close as intended.
|
These are the repercussions of the alert being set
|
No
|
|
|
The electrical hardware for the glovebox will disable itself if it encounters an 'overtemperature' or 'overcurrent' condition. If this is a recurring problem, a module replacement may eliminate the issue.
|
The glovebox electrical hardware (High-Side Driver) reports an overtemperature fault
|
The glovebox will not respond for 15 seconds. May eventually lead to a totally inoperative glovebox if triggered consistently over a long period of time.
|
No
|
|
|
Motor calibration is usually performed as part of routine 0x170 for BCCEN. The calibration data is stored in the module's non-volatile memory.
|
Rake or reach motor is not uncalibrated
|
Automatic position recall disabled for affected axes, manual adjustment may stop working
|
No
|
|
|
Not Available
|
Error in communication.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Recall command for a profile that had never been set with a Store command.
|
These are the repercussions of the alert being set
|
No
|
|
|
The electronic control unit (ECU) detects that the supply voltages from 1 or more components are out of range.
|
The ECU detects the supply voltage is < 7.31V. Specific reason(s) should be available in alert log signal data.
|
The ECU may be unavailable.
|
No
|
|
|
Not Available
|
Error in communication.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Invalid authentication received.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
The desired state of the glove box light could not be set, the current state is not the expected one or the light did time out
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Switch is active for 30 seconds continuously or has been misused.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Glove box or front trunk status is open when valet mode is true.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Add the alert trigger conditions here
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Add the alert trigger conditions here
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Rail value does not match GTW request value after 500ms. Rail state is unknown.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Wipers are commanded to move but the park position is not detected for 10 seconds. Wipers are commanded to move but the park position is detected continuously for 2 seconds.
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Add the alert trigger conditions here
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Add the alert trigger conditions here
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Add the alert trigger conditions here
|
These are the repercussions of the alert being set
|
No
|
|
|
Not Available
|
Add the alert trigger conditions here
|
These are the repercussions of the alert being set
|
No
|