Alerts
Loading...
| Signal Name | Description | Condition | Impact |
|---|---|---|---|
|
No hardware audio devices available in the system
|
Hardware audio devices intialization failed and will be re-tried
|
No audio
|
|
|
The Center Information Display (CID) reported firmware version does not match the vehicle firmware version reported by the Gateway.
|
The Center Information Display (CID) reported firmware version does not match the vehicle firmware version reported by the Gateway.
|
A potential degradation of the User Interface (UI) experience or lack of communication between the UI and vehicle.
|
|
|
The tegra MCU failed to communicate to the audio DSP over SPI
|
Failure to write/read to/from the audio DSP
|
-
|
|
|
The navigation service encountered an error when processing a navigation request.
|
Navigation service reports an error when attempting to navigate to a destination.
|
Navigation service falls back to offline routing. This can occur even if the vehicle has connectivity.
|
|
|
The Instrument Cluster (IC) reported firmware version does not match the vehicle firmware version reported by the Gateway.
|
The Instrument Cluster (IC) reported firmware version does not match the vehicle firmware version reported by the Gateway.
|
A potential degradation of the User Interface (UI) experience or lack of communication between the UI and vehicle.
|
|
|
The User Interface (UI) main application, also known as QtCar, is intentionally rebooting due to a user-initiated action.
|
QtCar receives a valid request to reboot, such as a user-initiated software update or a settings change that requires a restart.
|
QtCar will temporarily be unavailable during reboot, which may cause a brief interruption to the user's interaction with the vehicle's systems.
|
|
|
The User Interface (UI) Electronic Control Unit (ECU) detects one or both of the cellular antenna is experiencing a connection condition.
|
The cellular antenna load measurements are outside normal bounds.
|
The cellular connection signal reception and data throughput may be reduced.
|
|
|
An error with a User Interface (UI) database was detected and the automatic recovery was not able to restore its functionality. Therefore some data from this database may be missing or incorrect and dependent features may not function as expected.
|
Database corruption recovery mechanism fails, triggers on each failed automatic recovery attempt.
|
Impacts specific UI features dependent on the affected database.
|
|
|
The display manager detects an error with the Field Programmable Gate Array (FPGA) dedicated to the rear view camera.
|
The display manager detects an error with the FPGA for the rear view camera.
|
The rear view camera may be unavailable or not operate as expected.
|
|
|
Alert indicating a UI process has exited with an error, payload contains the exited process name and exit signal.
|
UI process exits with error.
|
A process stopped unexpectedly. Depending on the specific process, some features may be unavailable.
|
|
|
The sandwich sensor is disconnected.
|
The frequency reading is > 38kHz
|
The classification cannot be performed
|
|
|
The sandwich sensor is low.
|
The frequency reading is < 22kHz but > 1kHz
|
The classification cannot be performed
|
|
|
The sandwich sensor is shorted to ground.
|
The frequency reading is < 1kHz
|
The classification cannot be performed
|
|
|
The cushion self capacitance sensor is open.
|
The frequency reading is > 45kHz
|
The classification cannot be performed
|
|
|
The cushion self capacitance sensor is low.
|
The frequency reading is < 25kHz but > 1kHz
|
The classification cannot be performed
|
|
|
The cushion self capacitance sensor is shorted to ground.
|
The frequency reading is < 1kHz
|
The classification cannot be performed
|
|
|
The seatback self capacitance sensor is open.
|
The frequency reading is > 45kHz
|
The classification cannot be performed
|
|
|
The seatback self capacitance sensor is low.
|
The frequency reading is < 25kHz but > 1kHz
|
The classification cannot be performed
|
|
|
The seatback self capacitance sensor is shorted to ground.
|
The frequency reading is < 1kHz
|
The classification cannot be performed
|
|
|
The sandwich sensor is not calibrated.
|
The calibration value saved in flash is invalid
|
The classification cannot be performed
|