Alerts
Loading...
| Signal Name | Description | Condition | Impact | Important |
|---|---|---|---|---|
|
Left Front Wheel Speed Sensor: Plausibility against second signal failed due to monitoring of wheel speed differences.
|
Large wheel speed diff relative to other sensors detected
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Left Front Wheel Speed Sensor against second signal failed due WSS signal interferences or disturbances.
|
WSS signal interferences or disturbances
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
A wheel speed sensor with wrong sensor type is mounted on wheel front left.
|
A wheel speed sensor with wrong sensor type is mounted on wheel FR.
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
WSS fault due to missing wheel speed signal.
|
No stop pulses occurred on WSS
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
WSS fault due to missing wheel speed signal.
|
Wss fault due to missing wheel speed sensor signal
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
WSS_FL HET TU buffer noise (enormous amount of edges ocurred).
|
Signal from WSS is noisy/implausible
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Maximum wheel speed reached. Range monitoring for WSS signal which monitors non-plausible high wheel velocity.
|
Range monitoring for WSS signal which monitors non-plausible high wheel velocity
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
WSS_FL line interruption (sensor or supply line).
|
WSS line failure (no exact failure reason detectable).
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Short circuit of the WSS_FL sensor line to 12V.
|
Short circuit of the wheel speed sensor line to + voltage.
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Short circuit of the WSS_FL sensor line to GND or line interruption (sensor or supply line).
|
Short circuit of the sensor line to GND or line interruption (sensor- or supply line) .
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Reverse current at wheel speed sensor supply detected and the reverse protection switch is switched off.
|
Backward power supply of ECU via WSS supply line is detected. One of the WSS power supply lines is shorted to Ubat.
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Wheel Speed Sensor: General Fault.
|
More than one suspected wheel speed sensor failures occur at the same time for more than 500ms. A suspected wheel speed sensor failure is set in the following situation: Noise monitoring- slip monitoring- dynamic monitoring- monitoring of absent signal or monitoring of flat tire sets a suspicious flag.
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Wheel Speed Sensor: General Fault.
|
This error will be set if 2 rotation directions of the sensor signal are in one direction, the other 2 rotations are in the other direction OR 2 rotation directions of the sensor signal have no rotation, 1 rotation in one direction, 1 rotation in other direction
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Wheel Speed Sensor: General Fault.
|
If the difference between maximum and minimum wheel speed related to a reference speed exceeds 5%. A generic wheel speed sensor fault is set if no wheel specific fault could be determined. During system mode ABS and backup-EBD (Electr. Brake Force Distribution) and below 20 kilometers per hour the deviation is 6 kilometers per hour for velocities < 100 kilometers per hour and 6% for a velocity > 100 kilometers per hour.
|
Will disable VDC/TC and degrade ABS
|
No
|
|
|
Wheel Speed Sensor: General Fault.
|
Three or more sensor signals seem to be affected by temporary failure suspicion at the same time (one or several of the above described failure monitoring are triggered by not plausible or missing WSS signals).
|
Will disable VDC/TC and degrade ABS. Leads to deactivation of BSC and EBD.
|
No
|
|
|
ESP/ABS unit voltage is high.
|
ESP has detected PARTY or CHASSIS CAN network is under-voltage.
|
May disable VDC/TC and degrade ABS
|
No
|
|
|
ESP/ABS unit voltage is high.
|
Voltage at ESP supply pins exceeds specifications
|
May disable VDC/TC and degrade ABS
|
No
|
|
|
ESP/ABS unit voltage is high.
|
Voltage at ESP supply pins exceeds specification
|
May disable VDC/TC and degrade ABS
|
No
|
|
|
Wheel speed sensor supply voltage low.
|
HW issue in WSS power supply lines
|
May disable VDC/TC and degrade ABS
|
No
|
|
|
ESP/ABS unit voltage is low.
|
ESP has detected PARTY or CHASSIS CAN network is under-voltage.
|
May disable VDC/TC and degrade ABS
|
No
|